5′ Hydraulic Shore 34-55″ – Pacific Shoring

$1,105.00

Maximize crew safety and jobsite efficiency with this compact 5-foot aluminum vertical hydraulic shore.

  • Working Range: Perfectly sized for narrow 34 to 55-inch utility trenches.
  • Ultra-Lightweight: At just 70 lbs, it ensures effortless transport, staging, and positioning.
  • Zero-Entry Safety: Fully folds, deploys, and pressurizes completely from outside the excavation.
  • Target Applications: Engineered for water, gas, sewer taps, and localized spot repairs.

  • Warehouse Shipping Locations: California, Texas, North Carolina

 
SKU: PSV-05-34-55-HB Category: Brand:

Description

5′ Tall Hydraulic Trench Shoring with 34–55″ Range – Pacific Shoring

The Pacific Shoring PSV-05-34-55-HB is an aluminum vertical hydraulic shore designed to support opposing trench walls in utility excavations ranging from 34 to 55 inches wide.

This two-cylinder shore uses a 60-inch vertical rail configuration with two 2-inch hydraulic cylinders positioned approximately 12 inches and 38 inches from the top of the rail. Its working range makes it practical for service trenches, utility taps, pipe connections, spot repairs, and other localized excavations where a full trench shield may be unnecessarily large or difficult to position.

The PSV-05-34-55-HB features aluminum construction and a hinged design intended for installation and removal from outside the excavation. The shore can be lowered into the trench in a folded position, opened against the trench walls, and pressurized using a compatible hydraulic hand pump.

This individual shore does not have a standalone soil-depth rating. Allowable excavation depth, horizontal shore spacing, vertical cylinder spacing, sheeting requirements, and permissible trench conditions must be determined from Pacific Shoring’s current manufacturer tabulated data by the project Competent Person.

Not sure which hydraulic shore is right for your project? Compare hydraulic shoring options, including available length and width variations.

Key Benefits & Crew Efficiency

  • 34- to 55-Inch Working Range: Designed for utility trenches and localized excavations.
  • 5-Foot Vertical Rail Length: Provides a 60-inch rail configuration for utility excavations and approved multi-shore arrangements.
  • Two 2-Inch Hydraulic Cylinders: Provide controlled hydraulic support between opposing trench walls.
  • Dual Cylinder Configuration: The upper cylinder is positioned approximately 12 inches and the lower cylinder approximately 38 inches from the top of the rail.
  • Aluminum Construction: Combines corrosion resistance with manageable 70 lb weight.
  • Outside-the-Trench Installation: Designed for placement, pressurization, and removal from outside the excavation.
  • Hydraulic Installation: Uses controlled hydraulic pressure to establish firm contact with opposing trench walls.
  • Compact Excavation Capability: Suitable for applications where excavation width must be controlled.
  • Modular Shoring System: Can be used with additional shores and approved sheeting according to the required system layout.
  • Utility-Focused Design: Practical for contractors, municipalities, public works departments, and industrial maintenance crews.

Product Specifications

Product Code PSV-05-34-55-HB
Product Name Pacific Shoring 5′ Vertical Hydraulic Shore — 34″ to 55″
Rail Length 5 ft / 60 Inches
Minimum Trench Width 34 Inches
Maximum Trench Width 55 Inches / 4′7″
Number of Cylinders 2
Hydraulic Cylinder Diameter 2 Inches
Upper Cylinder Location Approximately 12 Inches from the Top of the Rail
Lower Cylinder Location Approximately 38 Inches from the Top of the Rail
Unit Weight 70 lbs
Material Aluminum
Product Category Hydraulic Shoring
Manufacturer Pacific Shoring

Pricing & Logistics

Price: $1,105

Contact Iron Lot to confirm current pricing, availability, and more information on compatible hydraulic pumps, installation tools, replacement parts, sheeting options, and freight charges.

Freight & Delivery Coordination

The PSV-05-34-55-HB features aluminum construction for transportation and staging at utility excavation jobsites. Complete system weight will depend on the number of shores, pump equipment, tools, sheeting, extensions, and accessories included with the order.

We can coordinate delivery to contractor yards, municipal facilities, equipment locations, and active jobsites. Freight quotations are available for individual shores, complete hydraulic shoring packages, replacement components, and mixed underground-equipment orders.

Target Applications

The PSV-05-34-55-HB is designed for trench applications where the excavation width falls within its 34- to 55-inch operating range. It may be used around incoming utilities or alongside a trench box when the complete protective-system design permits.

Potential applications include:

  • water-service installation and repair
  • sewer-service connections
  • utility taps and tie-ins
  • small-diameter pipe installation
  • conduit installation and repair
  • gas-service work
  • electrical and telecommunications trenches
  • irrigation and drainage work
  • utility crossings
  • localized pipe exposure
  • spot repairs
  • plumbing and industrial maintenance
  • municipal and public works projects
  • street and easement excavations

The 5-foot rail length and hydraulic working range make this shore useful for localized utility work where excavation width must be controlled. It may also be incorporated into a stacked or longitudinally lapped system when additional vertical coverage is required and the configuration is permitted by the manufacturer’s tabulated data.

Suitability depends on trench depth, soil classification, trench-wall stability, excavation width, shore spacing, surcharge loads, groundwater, sloughing or raveling conditions, required sheeting, and the complete protective-system layout.

How Vertical Hydraulic Shoring Works

Vertical hydraulic shores are compressive support elements installed between opposing trench walls. Once properly positioned and pressurized, the shore creates firm contact at each rail and cylinder location.

The system relies on soil arching between shores. Where soil is likely to slough or ravel, approved sheeting is installed behind or between the vertical rails to retain loose material.

The PSV-05-34-55-HB is hinged so it can be:

  1. folded for placement
  2. lowered into the excavation from outside the trench
  3. opened against the opposing trench walls
  4. depressurized and folded before removal

Workers must remain within the properly shored area whenever entering, exiting, or working in the excavation.

Hydraulic Pressure and Cylinder Capacity

Pacific Shoring’s installation procedure calls for hydraulic shores to be pressurized between 750 and 1,500 PSI.

After pressurization:

  • the pressure gauge should hold steady
  • the system should show no pressure loss
  • both rails must maintain firm contact with the trench walls
  • the shore must not be loose or able to move
  • the hydraulic hose should be removed and protected from dirt and contamination

Hydraulic cylinder capacity must be confirmed for the exact shore configuration. Cylinder capacity does not replace the manufacturer’s spacing tables or permit use outside the tabulated system requirements.

Soil Classification and System Selection

The soil must be classified immediately before the hydraulic shores are installed. Soil conditions can change during the project and may require shores to be repositioned, additional shores to be installed, or horizontal spacing to be reduced.

Pacific Shoring’s tabulated data states that vertical hydraulic shores must not be used in OSHA Type C-80 soil.

The selection guide is based on defined loading conditions that include equipment weighing 20,000 lbs or less and a spoil pile no more than 2 feet high, with the applicable setback requirements. Additional or heavier surcharge loads must be evaluated by the Competent Person, and shore spacing may need to be reduced.

Any alteration to the shore or variance from the manufacturer’s tabulated data requires a site-specific plan prepared and approved by a registered engineer.

Shore Spacing and Placement

The PSV-05-34-55-HB is one component within a complete hydraulic shoring layout. The number and placement of shores are determined by the manufacturer’s tabulated data rather than by the dimensions of one shore alone.

Important placement requirements include:

  • maintain the required horizontal shore spacing
  • maintain a maximum 4-foot vertical cylinder spacing
  • place the upper cylinder within the permitted distance below the top of the excavation
  • place the bottom cylinder no more than 4 feet from the excavation bottom
  • maintain contact with the soil at each cylinder location
  • account for trench length when determining the minimum number of shores
  • keep workers inside the properly shored portion of the excavation

For trenches 6 feet deep or less, the tabulated data permits one hydraulic cylinder per vertical spacing increment when the cylinder is positioned no more than 4 feet from the excavation bottom and no more than 2 feet below the top.

Hydraulic shores may be stacked or longitudinally lapped when the required spacing is maintained. These configurations must follow Pacific Shoring’s tabulated data and the Competent Person’s protective-system plan.

Sheeting Requirements

Sheeting is not treated as the primary structural element of the vertical hydraulic shoring system. Its purpose is to prevent soil from sloughing or raveling between the hydraulic shores.

Sheeting is required whenever sloughing or raveling is likely to occur. When used, it must extend to the top of the excavation and reach the depth required by the manufacturer’s selection table.

Approved sheeting materials identified in the tabulated data include:

  • specified CDX plywood configurations
  • specified exterior plywood and form panels
  • Pacific Shoring aluminum sheeting
  • approved timber lagging
  • minimum 1/2-inch-thick steel plate
  • equivalent approved HDPE or timber products

Sheeting may be attached to the hydraulic shores or installed separately behind the rails. Material, thickness, width, and installation depth must comply with the current tabulated data.

Critical Selection & Safety Factors

Is the PSV-05-34-55-HB Right for Your Excavation?

This model is a practical choice when the trench width remains between 34 and 55 inches and the complete protective-system design allows a 5-foot vertical hydraulic shore with two 2-inch cylinders.

This shore should not be selected solely because the trench falls within its width range. The complete hydraulic shoring system must satisfy the manufacturer’s tabulated spacing, soil, loading, sheeting, and installation requirements.

Installation and Pressurization

Installation must be performed from outside the excavation using a compatible pump, hydraulic hose, pressure gauge, and release tool.

Voids at a rail or cylinder contact point must be addressed using an approved solid block to the trench bank. The excavation faces should be vertical, and each shore must maintain proper contact with the soil.

Refer to Iron Lot’s comprehensive guide for more information on hydraulic shoring installation and removal.

Inspection and Removal

The shored excavation must be monitored for changed conditions. The manufacturer calls for inspection at the beginning and middle of the shift, with additional inspection when conditions change.

Loose shores must be removed and replaced. Shores left in place overnight must be inspected before workers reenter the trench.

Before removal, hydraulic pressure must be released with the proper tool. Pulling a hydraulic shore without first releasing the pressure can damage the unit.

Removal should proceed from outside the excavation and remain coordinated with pipe bedding, initial backfill, and the approved protective-system sequence. View Iron Lot’s guide on hydraulic shoring inspection and safe use for more information.

Safe Handling and Use

Important handling practices include:

  • install and remove shores from outside the trench
  • keep workers clear of suspended equipment
  • use a tag line when lifting larger shores with equipment
  • keep hands away from hinge blocks and moving connections
  • maintain safe hand placement when opening or folding the shore
  • use lifting equipment when a unit cannot be safely handled manually
  • keep unnecessary personnel and equipment away from the trench edge
  • do not permit workers beneath a loose or depressurized shore
  • use remote compaction methods outside the protected area
  • maintain safe access and egress
  • discontinue work when evidence of trench-wall collapse or protective-system failure is observed

The contractor and Competent Person are responsible for developing a safe installation and removal procedure for the specific excavation and ensuring that workers are trained before using the equipment.

View Hydraulic Shoring Guides

Request a Quote from Iron Lot

We supply Pacific Shoring vertical hydraulic shores, hydraulic pumps, installation tools, sheeting, trench boxes, manhole boxes, road plates, and related underground construction equipment.

Contact our team for current pricing and availability, complete shoring packages, multiple unit orders, freight options, and more product information.

Shop Trench Safety Equipment

Warehouse Shipping Locations: California, Texas, North Carolina

 

Payment Options:

We accept company check, wire transfer, ACH, and credit card payments. We also offer financing through Ascentium Capital.

Financing: Ascentium Capital offers fast and flexible financing. With their quick and convenient way to purchase equipment, working with Ascentium Capital helps you acquire the funds you need for your equipment purchase. With financing and leasing of up to $2,000,000, Ascentium Capital works with you to make the application process simple and at no obligation.

To learn more about Ascentium Capital and how it can assist you, click image below:

 

 

Ascentium Capital Equipment Financing

 

Call Iron Lot at 336-516-8011 or request a quote online for current pricing, availability, and freight information.

Product Specifications

Weight 70 lbs
Dimensions 55 × 12 × 60 in
Model

Pacific Shoring – Hydraulic Shoring

Material

Aluminum

System Type

Hydraulic Shoring

Manufacturer

Pacific Shoring

Range

34-55"

Number of Cylinders

2

Reviews

There are no reviews yet.

Be the first to review “5′ Hydraulic Shore 34-55″ – Pacific Shoring”

Your email address will not be published. Required fields are marked *